Design your steel frame composite gate
Pick the height, width, top, steel and colours. We'll show you a picture of your gate, then price it properly. Built in our Darwen workshop and fitted across Lancashire.
Welded steel core, galvanised
Powder coated to any RAL
Made to your exact opening
Free survey, fixed price
Build your gate, option by option
Seven choices, a picture of every option, and advice on each one. All option photos are shot in our standard satin black powder coat: pick another finish and it's applied in your full design preview.
What do you need?
Pick the job first. The width options change to suit it.
AdviceTwo leaves meeting in the middle. A standard single drive opening is 3.0m to 3.5m; anything from 4.2m up needs the heavier frame so the leaves don't sag.
How tall?
Measured from the ground to the top of the frame.
AdviceOur most common height, head height, full privacy for a garden or side access. Normally no consent needed.
How wide?
The opening between your posts or piers, or the length of the fencing run.
AdviceThe usual size for a standard Lancashire drive. Comfortable for most cars and a caravan.
Top design
Finials, a flat top, or an arch. This is the part people notice from the road.
AdviceClean, modern, level top rail. The best choice if you want the gate to disappear into the fencing line.
Frame colour finish
Powder coated after welding, so the colour goes into every corner. Standard is satin black.
AdviceThe safe, sharp choice against composite boards and brickwork. Our most requested finish.
Every picture above is our standard satin black powder coat. Pick another finish here and it is carried through to your full design preview, so you see the gate in the colour you actually want.
Board layout
Boards upright or laid flat. Same gate, same boards, different look.
AdviceBoards standing upright. The modern look most people picture, and the strongest option on a tall gate.
Composite colour
The boards that clad the frame. Same batch as any fencing we build with it.
AdviceThe default for a reason: modern, low maintenance, hides road dirt better than anything pale.
Not sure about something? Leave it and tell us in the notes. We measure the real opening at the survey, including sloping drives and out-of-square walls.
Optional
See it on your own drive
Photo of the gap, the old gate or the fence line, and we'll build your new gate into it. Best from a few steps back, straight on, in daylight.
Skip it if you'd rather not, the design still works without it. Photos are stored publicly (anyone with the link can open them), so only send a shot of your boundary, not of your family.
Your preview
See it before we build it
Choose your options, then generate a picture of your gate.
Illustrative only, watermarked with our logo. It shows style, proportions and colours, not the exact board profile. Your gate is measured and built to your opening.
Your specification
- What you need
- Double driveway gate
- Frame height
- 1.8m
- Frame width
- 3.5m pair
- Top design
- Straight / squared
- Frame finish
- Satin black (RAL 9005)
- Board layout
- Vertical boards
- Composite colour
- Anthracite grey
Fastest route to a price
Send this design straight to our team
Every option comes across with your design, so we can come back with a fixed fitted price the same or next working day.
WhatsApp opens with your specification already written out and a link to the design picture. On a phone the picture is attached for you as well.
What sizes do steel frame composite gates come in?
These are the sizes we build most often, and the sizes worth measuring your own gap against before you start. Nothing is set in stone: every gate is made to the opening in front of us, so odd widths, sloping drives and out-of-square walls are all normal jobs.
| Gate or frame | Typical size |
|---|---|
| Single gate | 0.9m wide |
| Single gate | 1.0m wide |
| Single gate | 1.2m wide |
| Double driveway gate | 3.0m opening |
| Double driveway gate | 3.5m opening |
| Double driveway gate | 4.2m opening |
| Frame height | 1.2m / 1.5m / 1.8m / 2.0m |
Measure the opening, not the old gate
Measure between the posts or piers at the narrowest point, and again at the top. Old gates rarely sit square.
Check the ground first
Sloping drives need the gate raised on the low side. That changes the finished height, so it's worth telling us early.
Height rules
Under 1m next to a highway, under 2m elsewhere, and no consent is usually needed. Above that, planning permission normally applies.
Steel frame composite gate questions
How much does a steel frame composite gate cost?+
It depends on the width, the height, whether the top is arched or finialled, the steel spec and whether you want fencing built with it. Design your gate above and send it over, and we'll come back with a fixed, fitted price within 24 hours. There is no charge for the survey or the quote.
Do I need planning permission for a composite gate?+
Usually not. As a rule, a boundary next to a highway should stay under 1m and anywhere else under 2m without consent. Taller gates, or a gate onto a main road, can need permission. We check the position and height on the survey and tell you before anything is built.
What is a steel frame composite gate made of?+
A welded box steel frame, galvanised to stop rust, then powder coated in the colour you pick. The composite boards are fixed to that frame. There is no timber core to rot and nothing to treat or paint.
What standard sizes do you build?+
Single gates at 0.9m, 1.0m and 1.2m wide, double driveway gates at 3.0m, 3.5m and 4.2m openings, and heights of 1.2m, 1.5m, 1.8m and 2.0m. Every gate is made to your actual opening though, so odd sizes and sloping drives are normal for us.
Will the gate match my existing fencing?+
If we build the fencing too, yes, the same boards come from the same batch so the colour is identical. If you already have composite fencing, send us a photo and the make if you know it, and we'll match as closely as the market allows.
Can the gate be automated later?+
Yes, but tell us at design stage. Automation ready frames get extra bracing and hinge points, which is far cheaper than rebuilding the gate later. Sliding kits need side room to run into, so it is worth mentioning even if you are not sure.
How do the AI design previews work?+
The preview is a visual guide generated from the options you choose, watermarked with our logo. It shows the style, proportions and colours, not the exact board profile or the finished article. Your actual gate is surveyed and built to your opening.
Prefer to just talk it through?
Tell us the size of the gap and what's around it, and we'll guide you through the steel, the top and the colours on the phone. Free survey across Lancashire, fixed fitted price within 24 hours.
